Friday, 22 April 2011

Keyless Entry - keyless deadbolt, keyless


For years we have been using a key pad activated deadbolt for front doors in our various homes - no keys to lose or give to various family members - only four digit codes. Up until now, all of the key pad units we have installed, extend and retract the deadbolt using a small battery powered electric motor.



This issue we've encountered is when the batteries become weak, the motor (in some cases) does not have enough power to retract the bolt and we must revert to another entrance to get into our home. Although these unit allow one to use a key to override the electronics, we never seem to have the key "on us" when it's needed. Fortunately we have a keypad on our garage door and that serves as an alternative entrance when this occurs. These deadbolt retraction failures have been occurring more and more often even with fresh batteries. I suspect the motor is or has worn out.



With this in mind, I shopped the market for an electronically activated dead bolt with manual bolt action. In other words, instead of a motor extending and retracting the deadbolt, one would use a lever or knob to perform this function. The keypad (electronic segment of the unit) would serve to activate the manual knob or lever. I found the Schlage BE365VCAM619 Camelot Deadbolt Keypad, Satin Nickel on Amazon at an extremely reasonable price and it has all of the features I wanted - electronic key pad activation, manual extension and retraction of the deadbolt upon activation.



The unit arrived yesterday and after a few problems with the unit being confused as to whether the bolt was retracted or extended (my fault), the unit works perfectly. Note, I already had a deadbolt lockset on the door, so it was a simple process of removing the old, and installing the new.



It's an extremely high quality unit without the cheap plastic casing my prior unit had on the inside casing. It's all metal. Changing or adding key pad codes (combinations) is relatively easy. One must enter the units six digit master code (don't lose this code, keep it in a place that you can go to each time you wish to change the codes - Using a permanent marker, I wrote it on the inside of the lock), and then enter your personal four digit code. We use two codes however the unit can store many codes. You may want to add a temporary code to let a service technician into your home, then delete that code when the work is completed.



One feature I like is the lighted key pad which our old unit did not have. If we forget to turn on the porch light, by simply pressing the "schlage" button at the top of the keypad, the keys light up.



Here's the basic operation.



When you're leaving the house, close the door, press the "schlage" button, wait for the click, then extend the deadbolt. You'll hear a confirmation click confirming that the locking knob/lever has been disengaged from the deadbolt after the deadbolt has been extended.



When you arrive home, simply enter your four digit code, you'll hear a click, then manually retract the deadbolt and enter the home. I you wish to use the keypad light; simply press the "schlage" button to light it up. Obviously this is not needed during daylight hours.



Basically the nine volt battery is operating the keypad, a knob/level engagement solenoid and the keypad back light and should last for hundreds and hundreds cycles.



Bottom Line - I highly recommend this high quality unit. Schlage BE365VCAM619 Camelot Keypad Deadbolt, Satin Nickel

I have had the brass version of this deadbolt for bout a year and I love it. It is th best one that I have come across (and yes - the most expensive - but you get what you pay for). It is eye-catching rather than an eye-sore. Be careful, some of the cheaper competitor's models have a plastic back that is very unappealing for a main door. The unit is smaller than many by requiring only a 9 volt battery because it does not lock/unlock the deadbolt for you. You do it manually.



Pros:

1) Appealing design (front and back - no plastic)

2) Smaller than most (due to use of 9v battery)

3) Keypad lights up when you touch it for nighttime entry

4) Never get locked out. Give the neighbor a temporary code to get in.



Cons:

1) Pricey ut you get what you pay for

I installed one of these for a client and it seems to be a good product as all the reviewers say. What no one has talked about however is the standard Shlage key that can also be used to open the lock. It seems to me that this would allow the possibility of using a "bump key" to open it. One of the benefits of digital locks is their immunity to bumping. If you want the keypad just for convenience, that is fine. Just remember that any lock that can be "bumped" provides zero security.

We were consistently running into problems with the number of house keys we had given out to: contractors, landscapers and house cleaners. At some point there's no way to track who's coming and going into your house and whether or not they left the keys.

This little gadget eliminates the issue. I can now program the lock with one-time or multiple use codes unique to each individual coming to my house. It installs as easy as any other deadbolt and programming new codes takes about 10 seconds. This has quickly become my favorite new gadget.

I purchased the Schlage electronic deadbolt to allow entry into our house in case I didn't have a key with me. It works very well. Only drawback that I see is that it needs to be placed on a solid door without a glass panel as the lock has a lever on the inside that operates the deadbolt. There is no option for key locking from the inside, only the lever. Locks only keep honest people out, so it's better to have a deadbolt that is key lockable from both sides if you have an exterior door with glass panels. No need making it easier for a thief to get in than is necessary. - Schlage - Keyless Deadbolt - Electronic Lock - Keyless'


Detail Products
Detail Reviews
Click here for more information


Keyless Entry - keyless deadbolt, keyless keyless deadbolt Keyless Entry - keyless deadbolt, keyless

Hdtv


I wasn't even in the market for a 3D TV, but when my Sony HDTV blew yet another bulb, I decided it was time for something new.



Initially, I planned on getting one of the new Sharp 60" Quattron models, and headed to a nearby big box store to check out the selection. Picture quality was most important to me, where I was willing to accept a plasma if it blew me away, but I was definitely siding towards LCD or LED. I wasn't too shocked to find that while plasmas were nice, they weren't "that" nice, and settled in to the Sharp.



On my way out, I thought I'd check a couple of the 3D displays, just to be 100% sure I wasn't making a purchase I'd regret as soon as 3D content became more widespread. I looked at a couple of Panasonic models with active shutter glasses, and found that the 3D looked acceptable, but the glasses weren't comfortable on my head or to my eyes. A DirecTV rep all but insisted that I look at a high-end Samsung model connected to a DirecTV receiver, and I immediately noticed that getting the thing to display 3D apparently required messing with the DirecTV remote, the Samsung remote, and continually re-syncing the active glasses. "No, thanks." I thought.



Then I noticed an unloved LG display, with a bucket (yes, an actual bucket) of scratched passive glasses. No way was this going to look good, but it wasn't like I didn't have a few minutes to spare.



I was absolutely blown away. By far, the best 3D experience I've seen. Standing about six feet from the screen, there was a scene from an IMAX documentary where a fish seriously looked like it came out about halfway between where I was standing, and where the TV was. And I could see parasitic fish on the nose of that fish, moving around. It was incredible, clear, and I knew it had to be pretty expensive. Much to my surprise, it was in the same league as the Panasonic models. I had to have it.



Doing more research online, I saw that Amazon's price was even better (better, in fact, than a national warehouse club sells the non-3D version of this TV for). I ordered on a Monday, and scheduled my (free) shipping for Thursday afternoon. The delivery people came 15 minutes from the start of my four-hour delivery window, with no hassle at all.



Out of the box, the picture quality on this TV is pretty awesome. Better than I remembered it being in the store, for sure. But, I did notice that motion seemed really... weird. I wasn't sure if it was my satellite receiver, or the TV, but things just didn't seem to move naturally. After spending some time adjusting the dejudder and deblur settings, I was able to make the motion normal. But then, I figured, I might as well calibrate everything. Using a combination of the calibration feature on the Life Blu-Ray and recommended settings on various forums, I was able to achieve an absolutely stunning picture. Seriously, this thing looks like it cost hundreds upon hundreds more when it's calibrated.



1080i / 1080p content looked absolutely brilliant. SDTV, on the other hand, isn't the best I've seen. It's certainly acceptable, and arguably on the better side of what's commonly found on LCD / LED models, but I'd probably consider getting something different if most of your viewing is going to be sub-DVD quality content.



Then it was time to break out the 3D. I snagged a copy of Tron: Legacy (Four-Disc Combo: Blu-ray 3D / Blu-ray / DVD / Digital Copy) and spent most of the movie sitting with a dumb smile on my face. The picture quality and depth were outstanding. Don't fall for the "active / passive" hype. Watching 3D content with the LG's passive glasses is certain to please anybody who can see. And going back to my memory of the Samsung set, when the LG detects 3D, a box pops up that tells you to put your glasses on. That's it. No messing around endlessly with modes to get it working.



I then decided to play with the 2D-to-3D function on some HD channels and standard Blu-Ray discs, and was actually pretty surprised. More often than not, the TV seems to process the image as you'd expect to see 3D. It's not something I'd want to do all the time, but I have to say, watching Moulin Rouge! [Blu-ray] with 2D-to-3D was actually pretty awesome.



The built-in applications were kind of a mixed bag. Getting the TV on my WPA2 wireless network was pretty simple, and the Wii-inspired remote worked better than I had expected. The Netflix and Amazon On Demand apps were both very solid -- arguably better than what you'd find on a Roku, and miles ahead of the ones built in to my Sony Blu-Ray player. The other apps were less than impressive. Bringing up the weather app is more time consuming than just tuning to the Weather Channel, for example. The included web browser is fine for "Hey, look what my TV can do" showing off, but you're probably not going to want to fire it up to look at IMDB in the middle of a show.



All things considered, this is probably the best value around. While I lost 5" of screen real estate over what I planned on buying originally, the difference in picture quality alone was a decent tradeoff. Getting 3D was gravy, to say the least. Unless this thing sets my house on fire, I'd be hard pressed to recommend anything else within a couple hundred dollars. LG Infinia 55LW5600 55-Inch Cinema 3D 1080p 120 Hz LED HDTV with Smart TV (Included: Four Pairs of 3D Glasses)

I have to say I was really impressed by this set when i first saw it being demoed. I love 3d but have never wanted to own a set because the active shutter 3d makes me dizzy and sick after about 10 minutes of watching it. The passive 3d offered by this system is great. No sickness, little to no eye strain and a great 3d image. People have complained that the way the 3d is created halves the resolution, this is not noticeable at all with 3d blu-ray. I did notice lining in the image when i was very close to the tv, closer than I would want to sit comfortably. One complaint I have, though it is a small one, is that 3d gaming is noticeably lower in resolution. I have only tried this with one game(killzone 3) and only with this 3d format so cant really compare weither the other 3d format(active shutter) offered would be better for gaming. Still an amazing gaming experience regardless.'


Detail Products
Detail Reviews
Click here for more information


Hdtv Hdtv Hdtv

Digital Photo Frame - digital picture frame, digital frame


The Viewsonic Digital Photo Frame (10in) is an all-around great product for displaying those precious photos in your collection. The quality is extremely high and the cropping of photos seems to be realistic and nice. If a photo doesn't fit the frame, the resizing tends to distort the image slightly, but much less than other products of this type.



I highly recommend the 10 in digital frames; if you are thinking between the sizes, the size difference is quite worth it. Photos are easily seen from a slight distance and the overall appearance just seems nicer.



The main downside to this frame is that it only contains a 100 MB internal memory, which, with high quality photos only holds about 100-200 photos. However, it does contain a USB port and flash memory port for loading files, and the drag-and-drop method of loading images onto the frame is simple for even the most inexperienced user.



Highly recommended item. ViewSonic VFD1027w-11 10.2-Inch Digital Photo Frame with 128 MB Internal Memory

While this doesn't have a lot of memory, the quality of the frame is very good. I purchased a 4G SD drive to go with this and, even after that cost, this was option was cheaper than most other digital frames and just as nice. I chose this larger frame as this was a gift for my husband's grandfather as I thought the larger frame would be easier to see and i was right! I previously purchased a 7-inch frame but returned it as it was way too small for an elderly person to view the pictures, but this 10-inch frame was just right and he ended up loving this gift!

On a positive note, the picture quality and size of the pictures is very good. The frame has settings so you can adjust how long a frame is displayed. I have set it at 3 second intervals, however, the frame automatically switches from 5 to 15 second intervals sporatically. Also, the frame came with a remote to allow one to move forward or backward at will. This function also does not work consistantly. I will be calling the manufacturer to see if they have any suggestions. Perhaps it is just a bad unit?

This is a high quality product. The black frame is classy and the pictures display beautifully and brightly. It is extremely easy to use. I hooked it up to my mother-in-law's computer with a usb port and uploaded pictures to it. It includes the usb cord to fit a computer and the frame. It looks as if the cord would fit a standard camera as well. Though it says it will only display jpg files, it did display some bitmap pictures that I saved from facebook.



The frame offers a variety of functions. The slideshow offers several options for how long each picture is to be displayed. I think it goes between 3 seconds up to an hour, with a big jump from either 1 minute or 5 minutes to 15. There are also a handful of slide transitions to choose from. Pictures can be rotated in the frame using the remote, but I found that every time the pictures cycled through we had to rerotate some of them. Along the same lines, the frame will only correctly display either vertical or horizontal pictures.



I would definitely recommend this product. It made an excellent Christmas present for my mother-in-law. She LOVED it!

This is a nice frame, good picture, etc. Its rather large, too. The trouble is with Viewsonic as a company. We got our frame for Christmas. It occasionally locks up. Viewsonic support has been terrible at responding. They ignore email, and live support is only available during a small window of the day when I'm at work.



So if you get one that works fine out of the box, its great. If not, return it right away.

I bought this product for 65 bucks for my mother for Christmas. The quality was pretty good and the size was amazing especially for the price. The set up is easy and downloading pics onto a memory card and placing it into the digital frame is a breeze. I could easily work this frame without using the instructions. This overall was a great buy. Anytime you can find a digital frame of this size for 65 bucks.... get it.

I bought this as a Christmas present and I'm glad it was for my significant other so it can stay in the house.



The frame has a good size and one of the best resolutions on a digital frame that I have seen. The picture is bright with good contrast and detail.



The only thing I will mention is that I've found that pictures that are sized perfectly for the resolution look better than those that have to be resized by the internal processor. In other words, pictures that the internal processor resizes are a little fuzzy compared to pictures that I've cropped and resized in Photoshop. But this is a common "issue" with all digital frames that most people would never notice.

Excellent image quality, very bright. I bought one and loved it so much I bought 5 more for presents. I am using 8 Gig SD cards. It will only play JPEG stills and no video or audio.Love the big image size!

I gave this frame as a gift this Christmas. It was extremely well received. The display is excellent and the frame itself is beautiful, an excellent quality. It was easy to set up, and the remote works from eight feet away. The zoom feature also works very well. - Digital Picture Frame - Photo Frame - Digital Frame - Digital Frames'


Detail Products
Detail Reviews
Click here for more information


Digital Photo Frame - digital picture frame, digital frame digital frame Digital Photo Frame - digital picture frame, digital frame

Home Theater - receiver, home theater receivers


The sound from my ten year old Onkyo TX-DS474 was now inferior and I had read very good reviews of the Onkyo SR 507, so decided to pre order the brand new SR 508. It arrived from Amazon on April 29th. I used the built in equalizer to set up the speakers, connected the receiver with brand new HDMI v1.4 cables and connected it to my Dish satellite receiver, my Panasonic BluRay DVD player and my Panasonic HDTV. The sound was excellent. Whereas before we had to turn up the volume too loud to follow dialog on some shows, or else it was not clear, with the SR 508 the sound was so much clearer that we could keep the volume much lower.

After about three days I noticed that although I would assign the input as cab/sat, the receiver indicated ipod (now no ipod dock was connected to the receiver) but the sound still came through from the satellite box. Strange but no problem. Then exactly one week after receiving the receiver, in the middle of watching a show, the picture and sound went blank. No pushing of different buttons on the remote would make it work. My first reaction was a bad HDMI cable, so I changed it. Nothing. I switched to the DVD player, but again blank. So then I hooked up the satellite box and the DVD player directly to the TV by separate HDMI cables, turned on the TV speakers, and the TV works again. Obviously the SR 508 suddenly failed and would not even work as a pass through. I am returning the set to Amazon for a replacement. If the replacement works fine for a reasonable amount of time, I will update this review.

I chose Onkyo partially because of its RIHD feature in conjunction with Panasonic. In my experience that only works so-so. Turning on the BluRay DVD player did switch the receiver directly to DVD. But turning it off does not switch back automatically to cab/sat. Turning off the TV also turns off the Onkyo, but not vice versa. You still have to turn on the Onkyo receiver separately.

One unexpected problem with the receiver is that the zone 2 input works only with an analog signal. On my DS-474, I have set up output B to speakers in my screened in porch to be able to listen to CDs or TV there. The B speakers work with digital. Now all my signal inputs for zone 2 are digital, so it appears that the zone 2 feature is useless. Bummer!

I should specify that I am not at all techie, so there may be work arounds that I don't know!



Update#1: The unit failed Thursday evening, I requested a replacement online from Amazon on Friday noon, it arrived at my house on Saturday at about 2pm. I'm sure everyone would agree that that is outstanding customer service from Amazon. I have now (Sunday) installed the replacement unit and again it appears to be working great. Provided it continues to do so, I will add a second update and change my rating to four stars. I remain disappointed that the zone 2 is not digital, hence not 5 stars.



Update #2: Four days after installing the second receiver, it also failed in the same way. However, at the bottom of the "Troubleshooting" page in the user manual, I found the following comment: "The AV receiver contains a microcomputer for signal processing and control functions. In very rare situations, severe interference, noise from an external source, or static electricity may cause it to lock up. In the unlikely event this happens, unplug the power cord from the wall outlet, wait at least five seconds and then plug it in again."

That worked and it has not locked up again in the last ten days. However, I certainly take issue with the "rare circumstances" and "unlikely event" and I can't imagine any special event that may have caused it. My receiver is in a cabinet with the plug behind it, so unplugging is quite inconvenient. This said, the sound from the receiver is really clear so, if this problem does not recur frequently, I will be happy with the purchase. I'm changing my rating from one star to three stars. Onkyo TX-SR508 7.1-Channel Home Theater Receiver (Black)

I bought this to replace my Sony receiver I purchased from Amazon 3 years ago (almost to the day). While there was nothing "wrong" with my Sony receiver, I quickly realized once I plugged the Onkyo in, that my surround speakers were not being utilized as they should be.



While I am not an audiophile, I do have some quality speakers, and I do like having a quaility sound while watching movies (and playing Xbox). The sound is so clear and crisp with this receiver. Further, the set up with the 4 HDMI inputs made my stereo cabinet so much cleaner, and I got rid of all of my YRW and RBG wires. I am sure I could have invested another $300 and really got some really high end equipment, but honestly, the Onkyo is worth it. The funny thing is, I spent the same amount on the new Onkyo as I did on the old Sony, and the difference is just amazing.



The on-screen set up is great. It makes customizing the inputs and the equilizer so easy. And the speaker test really lets you know what where you need to place you speakers. What else can I say about this product? Honestly, this is the best purchase I have made in a long time. I think the 4 HDMI inputs alone make this a must-have over any other receiver similarly priced. I almost bought another Sony instead of the Onkyo (mostly because I have never purchased anything other than Sony receivers), but I am glad I made the switch. Now that I have experienced Onkyo, I think I have made a life long switch.



If you have any hesitations about buying this product, please feel free to send me a message, and I will try to answer your question before you buy. And if you have never bought an Onkyo before, try it first, and I am pretty sure you will like it (I would almost guarantee it). If not, return it to Amazon. They are really good with returns. But I doubt you will even want to return it once you get it set up. - Hdmi - Home Theater Receivers - Home Theater - Receiver'


Detail Products
Detail Reviews
Click here for more information


Home Theater - receiver, home theater receivers receiver Home Theater - receiver, home theater receivers

Tomb Raider Lara Croft - angelina jolie, fantasy


Why is it, that we want more from a movie than is on offer? Come on chaps, "Lara Croft - Tomb Raider" isn't a film of any intellectual merit, it is merely an exciting adventure movie with a whole host of good special effects and lots of quality funny moments. I for one really enjoyed this film, I expected nothing from it other than a series of explosions and gun battles and that is what I got and I loved every single minute of it. The plot wasn't too complicated, with Lara piecing together a mystery about an ancient clock and two pieces of a mystical triangle that has the ability to fragment time and space and of course there are the obligatory bad guys trying to get their hands on it. There was a fine cast of characters from Iain Glenn playing the evil Mr. Powell (the main bad guy) to Chris Barrie of Red Dwarf fame coming across with great aplomb as the overtly English Butler Hillary who tries and fails to make his young employer into a regal young lady instead of a gun-toting maniac. One of my favorite moments is when Hillary realizes that the security in the Croft Mansion has been breeched and there is a battle going on downstairs. He calmly gets out of bed, dons a bullet proof vest taken from his wardrobe, locks and loads a massive double barreled shot gun without blinking an eye then carefully steps into his leather slippers before stepping out to join the melee. I cracked up laughing, it was SO funny! Angelina Jolie is well cast as Lara Croft, and she manages a pretty good English accent too as well as doing ALL her own stunts which impressed me big time. The special effects were superb, watch out for when a husky-dog jumps through a break in the fabric of time, it's awesome. All in all this is fun, fun film and that is the way it should be treated. The DVD is worth every cent and is stuffed full of extras that just add to the enjoyment of the film. So come on chaps, give it a chance, you never know, you just might enjoy yourselves! Lara Croft: Tomb Raider

I give the movie 5 stars as an exciting imaginitive adventure movie.

But there are issues with the Blu-ray version - which are:

The movie was not photographically focused with HD video in mind. Sometimes the details are clearly in focus, sometimes the details are only DVD clear. This is better than an ordinary DVD "upconverted" but is not consistently what I would expect from a true Blu-ray quality movie. If you already own the DVD it may not be worth upgrading - but if you don't I think it is worth it for adventure movie fans.



This is based on the original Blu-ray disk release.

I've been loading up on big, dumb action movies on blu-ray, so when I saw this on sale for $10.99, I said why not... I popped the disc in, and was horrified at the picture quality- it looks like an upconverted dvd. If you have this on dvd already, then don't waste your money.

This has got to be the best attempt at a good game-based movie that I've seen. There were a few minor plot discrepancies that didn't quite follow the storyline of the game, but they could be ignored-I actually didn't notice them myself until my avid Tomb Raider-playing pal pointed them out. I loved the action sequences-the "ceiling ballet" being my favorite, and I think that Angelina Jolie did a suberb job portraying our feisty heroine. The music was probably the best part of the movie, though. The fast-paced techno stuck with me more than the actual story did, and I bought the soundtrack almost immediately afterward. What I didn't like was that the storyline of the movie wasn't that well developed. The charcters were typical, the events were ordinary, and the plot was so predictable that I found myself speaking the dialogue before the characters did! The story wasn't that detailed or involved. A third-grader could have followed it without trouble. I had been hoping for a more provoking, mature movie. Overall, it was...okay. Maybe the next ones will be better...that is, if they don't follow the rule of sequels...

I read so many bad reviews about this product, I was almost positive I would hate it. Then I came across the review Roger Ebert gave it for the Chicago Tribune. HE gave it 4 and half stars out of five. That peaked my interest. I found it at my Wal-Mart for $4. Figuring I could spare four bucks, I bought it, and watched it two days later. By far one of the best movies I've seen a LOOOONG time. Very intriguing plot, great acting, plus it's just plain fun. Combine Indiana Jones with Mission Impossible 2, and you have an idea what this is like. Plenty of special features to keep die-hard movie buffs happy. Plus it's got Angelina Jolie. Need I say more?

Yes, many people are bashing this movie but I think they are all wrong. That is why there is a sequel since it was a good flick, right?



This movie is a very good adaptation from a game, since I also love the games. Angelina was a good Lara Croft not just in the physical aspect but also in the attitude. She is as confident as the one in the games.



The movie also circles in a great plot line. The plot is very well served and not draggy, unlike other movies. It doesn't aim to much to inform people a lot about the Illuminati but supplies what the viewers need, not over or under that. The whole plot makes sense in a not so draggy way.



The adventure aspect is also well done. The exotic locations were mesmerizing as well as the action sequences. The stunts were very realistic, unlike the ones in movies like Charlie's Angels were people leap like animals. Here, Lara is very human but athletic, doing stunts that are actually possible to do and done very nice cinematically.



The movie overall is very enjoyable. its a fun action flick. It may lack depth or may fail to satisfy one but its an action flick. Let go and enjoy. - Angelina Jolie - Occult - Fantasy - Action'


Detail Products
Detail Reviews
Click here for more information


Tomb Raider Lara Croft - angelina jolie, fantasy action Tomb Raider Lara Croft - angelina jolie, fantasy

Iphone 3g Accessories


I ordered this cable because the image shows a real style Apple cable with rounded edges. I have an OtterBox case that requires a rounded edge cable in order to charge it. I received this cable and it is a generic square ended cable, which is completely useless to me. Though it might work it would require I remove the phone from the case every time I wanted to use it, which is not an option. White Sync & Charge USB Cable for Apple iPhone 3G / Apple iPhone 3GS

within days of a less than favorable review of this $.01 iPhone sync & charge cable, I received a call from the seller to inquire about the nature of my complaint. On my part, it was a minor inconvenience that the cable would sync but not charge. For a penny, I thought I got more than my moneys worth. He, however was dedicate to total customer satisfaction and I received a new cable, at no additional cost within 3 days.

That is Customer Service!

When my dog chewed through my iPhone adapter, I didn't want to spend $19 in the Apple store for a replacement. I considered replacing the dog, but instead I decided to find a cheap, compatible adapter. I found this one and I thought, "Well, if it doesn't work, I'm only out a couple bucks." I bought two of them, and the disadvantages were apparent right from the beginning.



First, as a previous reviewer mentioned, the business end of the cable is squared, not rounded. This wasn't a problem with my case, but it would be with others. Second, the construction and materials used leave a lot to be desired. There is no doubt when you look at this product that it is a cheap dollar store version, and that doesn't inspire a lot of confidence in it. Finally, my phone would not sync with iTunes. Considering iPhone users need to sync their phones to get crucial updates, that is a big problem. However, the cord did charge my phone, so it wasn't a complete loss. Or so I thought.



Within a week, through normal use, I broke the iPhone connector end on my cord. The plastic case came apart, and a few of the components fell out into my hand. The rest I had to carefully remove from inside the port on my phone. After a little tinkering, I was able to put the cable's connector back together, but it didn't fasten tightly. I remedied this by wrapping two small hair elastics tightly around it. The second cord lasted a few weeks longer, only falling apart recently. I was unable to repair the second. But hey, when held together with duct tape, chewing gum, and rubber bands, I still had one cord that charged my phone! Until just now.



The rigged up, cheap, piece of you-know-what cord decided about an hour ago to stop charging my phone completely. I don't know why. The components in the rubber-banded end are still secure, the connection is good, and it's plugged into a reliable power source. It occurred to me that though I saved a few dollars, I paid for it in hassles. Don't waste your money on this inferior product. Inferior is not even a strong enough word for what this product is; I don't think there's a word in the dictionary that quite captures the essence of crap that is this cord.

After reading all the negative comments, I didn't know whether to order the product or not. At last, I decided to give it a shot (rather than paying the high cost for the apple cable). When I received the cable, I tried to charge/sync my iPhone on a PC, a Mac, and with the wall charger - it didn't work. I contacted the company. Their answer was prompt and really kind.



Meanwhile, my girlfriend got herself an iPod touch. We tried to cable with her iPod - it worked. So, I decided not to return the cable. Then I went to an Apple Store and figured out in fact the problem was with my iPhone, not the cable. They swapped my iPhone, and right now the cable is working.



The cable is different than the original (the phone connector part is thinner). It comes in a nice box. Fast shipping. The customer service is great if your cable is not working - just make sure that the problem is caused by the cable. (They told me they were going to pay all the shipping, refund me for my return shipping, and send a new cable).

Cable works as described. Tested with an iPhone 3GS and it charges and syncs when attached to the computer. Works with the Apple branded USB to AC adapter that came with my phone.



The cable has two buttons that can be squeezed while inserting or removing from the phone. I actually prefer this to the OEM Apple cable which feels like I might break the small "hooks" when inserting into the phone.'


Detail Products
Detail Reviews
Click here for more information


Iphone 3g Accessories Iphone 3g Accessories

Pandigital Photo Frame - pandigital, digital picture frame


The Pandigital PAN7000DW 7" digital photo frame is the best digital photo frame I've found yet. I've purchased 4 other models in different sizes from Axion, Phillps, Smartparts, and Opteka. All of these others had various issues (16x9 when I wanted 4x3, didn't always start picture show automatically, buggy software).



The PAN7000DW is reasonably priced (about $65 from Amazon as of 11/9/2009) as compared to the Sony models which are all much more expensive.



The PAN7000DW display is excellent -- showing 800x600 pictures crisply and vividly. The software is very good with a reasonable user interface and useful options. I like displaying my photos using their original dimensions (the optimized view attempts to maximize the amount of display used but will chop off edges to accomplish this) - you can pick the view mode you want.



The frame accurately shows the EXIF photo date/time if you want to display it. It will also optionally show the current time. It has a nice calendar w/ picture view as well as the normal full frame photo view. And it seems to show ALL your photos eventually (I had a strange problem with an Opteka frame not showing all the photos, only a subset). The remote is small and is held on the back of the frame by a magnet. The remote works well (some remotes I've used have buttons that are hard to press or control). The menu structure (frame software) is logical and well arranged.



The clock functionality and auto turn on/off functionality is useful if you have power available to your frame at all times. However, I've hooked my frame up to a motion sensing power strip in my office and the time/date gets whacked when the sensor shuts off for the weekend (the time/date seem to survive for a few minutes or hours without power but not over a weekend). So if you use your frame with a motion sensing powerstrip, forget using the clock/calendar feature.



As I've discovered with many photo frames, if you want to display pictures in a particular order, they must exist in flash memory written down in that order - this is not a visible ordering - it does not depend on file name or file creation time. If you start with a totally empty flash card (or internal frame memory) then it will be the order in which the files are copied to the memory device. Macintosh and Windows file copy routines are the fastest way to copy files but the order in which copying takes place is not under your control if you move a large number of files all at the same time - the operating system parallelizes the copying for speed but this places the pictures in different physical memory order. It is too bad that most photo frames do not allow you to display in creation date order or EXIF date order or even file name order.



The best way to lay down the photos in sequence is to start with an empty flash device. Then copy the files either one by one by hand or using an automated method that copies files only one at a time. A cmd file on Windows that can do this is like:

-------

dir /b /od>c:\junk.txt

for /f "delims=*" %%i in (c:\junk.txt) do copy "%%i" f:\

-------

[...] (you need to change this script to fit your exact situation)



Alternatively you can use Photoshop Elements or some other photo management tool to export photos in sequence directly to a memory card or your picture frame.



Hopefully future photo frames will become a bit more intelligent and allow you to pick your display order.



Overall I've found the PAN7000DW to be a good value and to work as you would expect. Pandigital PAN7000DW 7-Inch Digital Picture Frame (Black)

I bought the Pandigital PAN7000DW so that I could load it up with pictures and videos of my new son and send it to my grandmother. After a few hours dealing with it (I'm very experienced with computers and electronic gadgets), here's my take:



- I like the look of the frame (classic looking) and the screen is bright and crisp.

- I could not get any video files to work. The documentation says it plays motion jpeg AVIs, and I tried many conversion options on my Mac using MPEG Streamclip and could not get it to work.

- Navigating the menus is a pain using the built-in buttons, so at first glance you're glad they included a remote...except the remote only registers about every 3rd button click, so you're constantly over clicking.

- The UI is pretty slow and lags your button presses.



All that said, it'll do what I want it to do. I've loaded it with 223 pictures at 1280x720 resolution, and it only takes up 34MB of the 1GB internal memory.

Right after I purchased a digital picture frame (about to become my Mom's 90th birthday present), the Pandigital PAN7000DW 7-Inch Digital Picture Frame (Black), I found an offer from Amazon Vine for a similar item, Smartparts SP72 7-Inch Digital Picture Wood Frame with Beige Matting (Espresso). Oh well -- it gave me the opportunity to compare-and-contrast the two frames (which are similarly priced). *I* didn't know which of these gizmos was best for the purpose, and I dare say you're just as unsure, so maybe my experience can help you.



The short summary: both these frames do what they claim to: They display your photos. But neither of them will give you a heartwarming feeling. The ideas are sound; the implementation kind of stinks. Perhaps more-expensive units have a better user interface, but these two frames are somewhat disappointing.



Let's start with the positives. The picture frames both have a 7" display, which is big enough for sitting on a desk or coffee table, and the displays are bright and clear. You do need a power cable, which might limit where you set up the frame; I can't see hanging them on a wall. The wood frame on the Smartparts is slightly nicer than the Pandigital, but both are reasonably attractive. The basic setup is extremely simple: stuff an SD memory card into the frame and turn it on.



A 2GB card holds 1000+ photos, depending on image resolution. That's a LOT of pictures, even when putting together a huge "this is your life" collection as we did for Mom. I bought a 4GB card along with the Pandigital, which would hold about 5,000 photos, and I could have saved a few bucks.



One thing that isn't clear from the documentation is that you don't HAVE to use an SD card. Both units have their own on-board memory that lets you add a decent number of pictures. You'll need to use the USB connection to get to that memory (and I never DID figure out how to delete their sample photos, grrr); more on that USB connection in a moment.



The Pandigital frame will also play MP3s, if you like. I didn't explore that feature because (a) my Mom's almost deaf and would never use it and (b) there are probably better options for playing music. The Pandigital can also be used as a clock and calendar, though I'm "eh" on that option myself; perhaps you care.



Other options are more important, I think. The Smartparts frame has an option for showing multiple pictures at a time (photo of mom on the left, then Pop's picture on the right, then fade to a third picture to replace Mom's photo). It really does look good, except that a 7" frame is too small to show most photos in enough detail to bother with this. Depending on how you use the frame, though, this feature could be useful. (Maybe for advertising purposes, such as in a realtor's front window, where the detail is a bit less important?)



Both frames have a USB connection, so you can plug them into your computer (mine's a Mac) and easily transfer JPG files to the frame or to the SD card you already stuffed into it. (That's a good thing, in the case of the Smartparts frame, since the card is a real pain to remove.) On the plus side, it means that I could choose a photo in iPhoto and export directly to the unit. On the downside, the Smartparts USB connection was very flaky; it would disconnect itself randomly -- usually in the middle of a file transfer. I used colorful curse words. You're probably best off to use whichever SD-card reader you already use to connect with your PC.



But truly the worst thing about these frames is a terrible, awful user interface for adjusting settings and for interacting with the unit. Both let you control the slideshow from buttons on the top or back of the unit. The Pandigital's are on top, which is slightly more convenient, but both are hard to read without a bright light nearby. The Pandigital also has a remote which (nicely) has a magnetic spot to hold it to the back of the unit. However, I give Mom about 20 minutes before she manages to lose it; it has the right dimensions to be a dandy cat toy, so I'm not upset that the Smartparts unit (which I'm keeping for myself, in case that's not obvious) doesn't have one. Plus, the remote's controls are sticky enough that it takes a few button-whacks to get the frame's attention.



Anyway, they both work with "OK" and "MENU" sort of buttons, and then up/down/right/left arrows to make selections. But the menu design is so poor that it's never clear when you want a right-arrow or a down one. (I never did get the clock set correctly on the Pandigital. Perhaps more detail was in its documentation, but I can't tell you. Other than a "getting started" flyer, the doc is on one of those tiny mini-discs which I feared would disappear into the maw of my iMac's drive. The Smartparts printed documentation is a little more extensive, but not much; a missing CD promised a Windows app, but I wasn't going to use it anyhow.)



Please note that you WILL need to mess with the settings. For one thing, the Smartparts frame seems to need to be told EVERY TIME to show pictures from the SD Card rather than from its own memory. The default time selection to show each photo (5 seconds) is probably too fast for what you prefer, one both units. (The Smartparts has slow/regular/fast; the Pandigital unit has specific time measurements, ranging from 5 seconds to one day.) Most irritatingly, both frames assume you want to choose the "optimal" display setting (well it does SOUND like what you want, right?). However, that actually means, "Make sure the photo touches the right-and-left edges of the frame, even if it means I chop off the heads of the people in the picture." The Pandigital unit automatically shifts the photo display based on whether you arrange it narrow side up or wide side up, but I can't see moving it around that much.



Despite our trained expectation of 5x7 photos, I came to the conclusion that these gizmos ought to be square to accommodate both horizontal and vertical photos. In reality, if I were to get serious about displaying the photos, I'd crop the images to make them get along with the gizmos' formatting; I wasn't about to do that with the 850 images I set up for Mom.



Bottom line: Both of these digital picture frames will get the job done. One isn't significantly better than the other, so I can't tell you to choose the Pandigital over the Smartparts or vice versa. No matter which you choose, though, expect to spend some time cussing before you finish with the setup. - Pandigital - Digital Picture Frame - Digital Frame - Pandigital Photo Frame'


Detail Products
Detail Reviews
Click here for more information


digital picture frame Pandigital Photo Frame - pandigital, digital picture frame

Verbatim Dvd-r - dvd, verbatim


I have already written a glowing 5 star review for the 25 pack spindle of these and will simply reiterate here that these are simply the best DVD blank media that I have used thus far.



I have used many different brands and must tell you that after burning to many tens of these disks I have yet to suffer a single error writing to them!



These burn very very fast at 16X in my pc computer's NEC ND-3500AG 16X DVD burner and also in my DMR-EH50S Panasonic DVD Recorder (through which I record content from the television to its hard drive and then after editing the content, burn it to DVD media).



I also want to let you know that there is extra storage space contained on these that I have not found with the many other brands I have used (including Taiyo Yuden, Philips, Maxell, Memorex, TDK)! I can squeeze more video and file content onto these Verbatim disks. That makes a difference in those critical moments in which I need to fit those extra few megabytes onto the same disk.



I will continue to use these exclusively until either the production quality goes down or they quit making them altogether -- I hope neither happens!



The price on these has been fluctuating lately, but no matter what the price, these are quite simply worth purchasing! It just so happens that at this particular moment (of writing) this 100 disk spindle has reduced in price to a mere $34.99. There is a $12.00 rebate for it as well!



After buying 3 25 pack spindles, I finally got wise and opted for the 100 pack. This should last me quite a while!



So get this 100 disk spindle now! I heartily recommend it to you! Verbatim 95102 4.7 GB up to 16x Branded Recordable Disc DVD-R (100-Disc)

Verbatim makes a very reliable blank DVD-R that can handle up to 4.7 GB of data. Moreover, these blank DVD-Rs record data at speeds up to 16x. I have used these as data discs, discs to record video and discs to record video. I also get very few, if any, coasters.



The DVD-R discs are compact and easy to store. While the discs are still blank, store them in the circular case on the spindle that they came in. After your burn data onto them, I would recommend storing them in slim jewel cases instead of paper sleeves. It's just better protection for your DVD-Rs that have data stored on them. Don't store these discs, burnt or blank, in rooms that become very hot; this causes damage to any brand of this type of disc and you could lose data over time.



There are two caveats that many other people note about any brand of this product: when you are burning the data onto the blank disc, don't be surprised if you see that the data is burning at a rate slower than 16x. This can happen if your burner doesn't have the capacity to burn faster, or it may be a quirk. I am not a professional so I cannot be certain of precisely what causes this phenomenon; but I assure you that the extra minute or two (tops) that you wait to get your DVD-R completed is worth the wait. In addition, DON'T write on these using Sharpie ink pens. The ink can seep through the top coating of the DVD-R disc and compromise your data



Overall, Verbatim blank DVD-R discs store data reliably and I believe that an extra minute to burn the data onto the blank disc is well worth it in the event that it doesn't actually burn at 16x.

I have ordered and used two sets of these and have never had a bad one. However Amazon shipping department have gotten a bit sloppy lately with their packaging for shipment.



Seems like they just grab any ole box (mostly too large for the item, throws the item in with a bit of very large bubble wrap and away it goes.



In my opinion, this method of packaging rarely protects the item and most of the time, the item(s) just rattles around inside. My wife and I have ordered a lot of things in the past year and have received the last few packages in this manner.



Back to the DVD-R media. I ordered this plus a couple of CD-R media. Being heavy and rounded the DVD-R came in with a broken outer casing. Luckily it didn't come apart and the media scattered all over the place which could have easily happened.



So come on Amazon! I've given you folks lots of KUDOS for your service and customer satisfaction, however your shipping department needs to be straightend out as they've gotten sloppy lately.

My first 100 stack was flawless. So i ordered another 100 stack a few months later. My second stack started to have write errors about a 1/4 of the the way down, and hoping that it was only 1 disc I pulled another DVD towards the bottom of the stack with the same results. I have so far burned 5 duds in a row with DVDs from various levels of the spindel. I've sent Verbatim support an e-mail hopfully to get a replacement, if that doesn't work i guess ill see if Amazon will make it right. - Verbatim Dvd-r - Blank Dvd Media - Verbatim - Dvd'


Detail Products
Detail Reviews
Click here for more information


Logitech Bluetooth Ps3 - harmony remote, logitech bluetooth ps3


I have a Logitech Harmony 1000 remote, and I run a Pioneer Elite receiver, a Toshiba HDDVD (ok - not smart), an XBox360, a wireless headset controller, a Pioneer Elite upscaling DVD player, two computers with Zalman IR controls, and a Playstation 3. I could control everything with my Harmony 1000 except the Playstation 3. I tried the Nyko Blu-Wave product, and while I've been extremely happy with most Nyko products, I had tons of problems with it. From not being able to power up/power down, commands executing twice, etc., there were just too many issues to make it worthwhile. Considering that Sony's bluetooth remote was so nice, it made sense to go to 2 remotes.



Well now I'm finally down to one without a sacrifice. This unit has it's own AC power, so it works whether the PS3 is off or on, which is a huge advantage.



The other huge advantage over every other solution is that it contains every single command that the bluetooth remote has (I believe it is 51 in all).



Pros:

-Self-powered via AC adapter

-Works regardless of PS3 being on or off

-Contains all 51 commands, including the PS button

-Doesn't take up a valuable USB port on the PS3

-Commands work in PS2 emulator of original 60gb PS3

-Range via Harmony 1000 is excellent

-No problems with double-commands like Nyko product

-Design matches Playstation 3

-Logitech had all the commands and screens for all of the supported remotes on their website on launch day (nicely done Logitech!!)



Cons:

-Price is a little high (it's 3 times the cost of the Sony bluetooth remote)

-For that money, I would like to have had the option of a rechargeable battery so that an AC adapter wouldn't be needed.

-Unit is small, but it seems like it could be smaller.

-It is still infrared from remote to receiver, so you have to aim it versus bluetooth which is omnidirectional.



Summary: If you want to get down to one remote, this is THE way to do it. If you want to save money, go with the omnidirectional Sony bluetooth remote (don't go third part on that). Logitech Harmony Adapter for PlayStation 3

EDIT: According to some of the comments below, Logitech has apparently FIXED the issue described below. In light of that, I give it 5 stars (unfortunately, Amazon does not allow you to change your original rating). However, for reference purposes, and in case someone encounters the same issue in the future (for whatever reason), I'm leaving my original review below.



Once you get this product, you'll be able to control your PS3 like any other device on your Harmony. It works well, doesn't lag, etc.



I started (naturally), unboxing. I thought the device would be bigger; it's slightly smaller than a deck of playing cards (not as thick). Plug in the AC Adapter (Yes, it's required. Otherwise, the PS3 couldn't be turned on by the Harmony, since USB on the PS3 doesn't provide power when the system is off.)



For those of you who have a higher with RF function, fear not; it has a plug for RF extension. I have a Harmony 520, so I cannot speak for the RF. IR range is very good, manual says 10M. I'm pretty sure the furthest I can get from the unit in the room it is setup in is about 13M, and it works fine at that range.



After unboxing, you turn on your PS3 the old fashioned way (Sony BT remote or controller), go to the settings part of the cross media bar interface -> Accessories settings -> Register BT Remote. Tap the orange button under the Logitech Unit, it registers.



Next up is the setup. And this is where I encountered problems. If the PS3 is your only unit, you shouldn't have any problems; however, if you have another gaming unit that takes IR, the setup can get REALLY confusing and frustrating. And, yes, I had the latest version of the software (7.5, but the software checks for any updates at startup).



So, I had the PS3 already added (tune in everything else) on my Harmony 520. Per the Logitech Support database recommendation, I removed the PS3 device and the "Use PS3" activity from my Harmony.



I readded it as recommended after this (Game Console w/ DVD, Sony, PlayStation 3, click through the advisory, OK.) Create an activity, update my Harmony, looking forward to use it instead of the Sony remote.



I run up the stairs like a young child at Christmas. Joyously, I hit the "Play PS3" activity. The TV turns on, the HDMI switcher goes to the right input, the PS3 turns on, the startup sound & video play...



I'm on the user selection screen (you see it if you have more than one profile on the console). I try to use the down arrow. It doesn't work. None of the soft buttons are there either.



Frustrated, I remove and readd the device + activity about 10 times. This takes about a half hour. Naturally, it's extremely frustrating.



Finally, I think "Why don't I remove the PS3 & Xbox 360 device and activities, then, I'll add the PS3 device, PS3 Activity, Xbox 360 device, and Xbox 360 activity, in that order."



Voilà! Everything works. Range is good, all the buttons work, including the soft buttons, etc.



IN SHORT: The product does what it says. For the extremely non-intuitive setup in a potentially common situation, I have to dock the unit 2 stars, especially in light of it's premium pricing.



IF YOU HAVE AN XBOX 360 OR ANY OTHER GAME SYSTEM:

-Remove ANY video game devices

-Remove ANY video game activities

-Add the PS3 as a device (Game Console w/ DVD, Sony, PlayStation 3)

-Add the PS3 activity (when you hit "add activity", it should be an automatic "Play Game" activity. You can rename it after you add it).

-Add any other video game devices and activities.



LOGITECH: If you read this, PLEASE fix the Harmony software for this type of situation. - Harmony Remote - Harmony - Logitech Bluetooth Ps3 - Logitech'


Detail Products
Detail Reviews
Click here for more information


Internet Cable - cat5, cat5e


If you choose to use a wire-based Internet connection, like my father and I did for security reasons, this cable is long enough to connect a laptop on one side of an apartment to an Internet modem on the other side of the apartment. The protective covering is still holding up after several months of usage, and it is 50 feet in length, as advertised. Even if your cable has a lot of slack because you only needed, say, 35 feet of cable, you can safely wrap up the portion that isn't needed and conceal it under furniture so you avoid tripping on it. CAT5e RJ45 PATCH ETHERNET NETWORK CABLE 50 FT WHITE

Got a new Samsung BluRay with Netflix capability on Black Friday. Problem was the TV and BluRay are in one room, and my DSL modem to connect to the internet is 30 feet away in another room. This was the perfect solution to that problem, at a very nice price! Works great.

The CAT5e RJ45 Patch Ethernet 50 White cable came in a timely manner. The cable works just fine the only exception is that the clip that locks the cable in place broke and I have to sometimes plug it back in. other than that the cable appears to be of good quality.

So, I make a living pulling data cable and the such; I speak with some authority on the quality of this cable. The ends of the cable are terminated on to quality ethernet tips but by no means the upper end of the spectrum. The tips have the tab that depresses the standard clear clip/tab to release the tip from the port which is a nice addition. The doubled up sheathing just before the tip looks decent but doesn't feel like it could take that much abuse. My biggest complaint with this cable is that it just is not very durable. The outer jacket that covers the cable is, by comparison to patch cables used on computer racks, just not very tough. I would say that if you expect any foot traffic whatsoever on your 50ft patch cable that you avoid this because it just simple won't last. Unfortunately I don't know the gauge standard for the durability of the outer jacket. If the cable is going to sit with little if any movement then it would be OK...The price is right though. I think a 50ft cable in tech outlets is much more expensive.

I only needed this cable to receive updates for my blue ray player and TV in another room. It is only used for short periods so for the price it works fine for me. If I were going to use it more permanently I probably would buy a more expensive cable.

This product is probably the most supple of cables I have felt. Why??? It is loaded with the thinnest wire I've ever touched!!! The wires inside this cable are 28 AWG - 28 is *V*E*R*Y* thin. The thinner the cable, the more resistance it gives. Compared to a 24 AWG cable of 50 feet (that I am replacing because of the blue color), the "ping" latency on my Mac went from 29 miliseconds to 374 milliseconds with this 28 AWG. I then plugged this into the Sony BluRay - It just couldn't keep up. I'm piping in 2.4Mbps, so there's never been a problem.



I feel really ripped off on this one and, for me, the loss of the free shipping on a better-built replacement (because I bought over $25 on my order, I got "super saver shipping.")



If you are just doing webmail, casual browsing, this will probably work. I would highly recommend that you avoid bending the cable at a sharp angle, pinching it under furniture, etc... The thin wires are more delicate.

This is a high quality network cable perfect for laptop users like myself who can't use wireless and want to be 'mobile' with their laptops. I have gone through several network cables trying to find a good one - and I believe this is it!



previous problems with other cables

- Don't last - the part of the cable near the connector gets twisted/flexible and eventually stops working. This cable has much sturdier connector 'housing' so there is no 'twist point'

- Connection isn't stable - I have had 3 cables that would lose their connection with the internet even without being unsnapped just from 'jiggling' the computer. This one never drops even as I'm dragging it down the hall. Beware of the cheap blue cables!

Being your average computer user, I needed something that would make my lap-top a bit more useful in my home. This cable allows me to use my laptop at various places on the second floor of my home. Until I decide on a wireless system, this will suit me just fine. - Ethernet Cables - Cat5 - Cat5e - Ethernet Cable'


Detail Products
Detail Reviews
Click here for more information


Bicycle Accessories - cycling, bicycle accessories


we purchased this seat a couple months ago for our daughter that was born in jan. 08. i installed it on a raleigh sc30. she absolutely loves to ride however, on my first run i noticed my heels interfered with the foot wells on the seat so i have to pedal with with my heels angled out and keep in mind i'm not a big guy i wear a size 9 sneaker. i accidentally dumped the bike tonight (with my daughter in it) at about 5 miles an hour into some grass and she was completely protected, also keep in mind she's a smaller baby though, she is 16 mo. and weights 17.5 lbs. best of luck on whatever you purchase Bell BV Caboose Child’s Bicycle Seat with Helmet

I've had this seat for 6 years or so and have been on many adventures with it. My only complaint was that the thin piece that keeps the child's legs from possibly getting caught in the spokes (something that happened to me as a child!) broke after a couple of years, and I've had to patch it in all sorts of ugly ways. When my daughter got near the end of the weight limit, which is 40 pounds, I started hitting her feet when I was peddling, I think because her legs were a bit long for the seat and were dangling out. - Cycling - Bicycle Accessories'


Detail Products
Detail Reviews
Click here for more information


Large Format Printer - pixma, pro9000


This product isn't quite listed correctly. It should be listed specifically as the Canon CLI8 Value Pack for the Canon Pixma Pro9000.



This particular printer model uses all 8 of these cartridges at once.



Listing Canon CLI-8 Value Pack BK/C/M/Y/PC/PM/R/G (0620B015) as I have stated, would prevent issues such as the gentlemen who wrote a review saying he had to return this item because he thought it was a double 4 pack so he ended up with 4 cartridges for which he had no use. Canon CLI-8 8-Color Multipack Ink Tanks

I recently purchased a Canon Canon Pro 9000 MKII to replace an Epson 2200 photo pinter. I find the print quality using this printer to be outstanding in comparison to the Epson. The color rendered by these inks are very accurate and the detail provided by the Pro 9000 MKII is easily seen as superior to the Epson 2200- as it should be since the Epson is 8year old technology.



I purchased the 8 ink tank multipack to tray and save money. I rated the multipack as 3stars because, while it is less expensive than buying individual ink tanks, a more cost effective option that Canon should offer is a 4pack that would include 1 cartridge each of Photo Magenta, Photo Cyan, Yellow and Cyan. These are the colors that are used by the printer by a factor of 2 to 1 of the others.

I've printed various Kodak C-print and Cibachrome papers in the darkroom over the last 30 years, and none come close to the quality I get with my Canon Pixma Pro9000 teamed up with CLI-8 inks. In addition, these inks outlast the photo materials and have a wider gamut as well.



I don't think you can find a lower cost than at Amazon.



When you want professional results, prints that you resell, there is no reason to experiment with cheaper, non-OEM inks. When you consider the time spent in the darkroom running test prints for color balance and exposure plus dry-to-dry times, these inks would still be a bargain at their full price found at the retail store. At Amazon, savings of 40% or more make a sweet deal!

Bought an expensive Canon Pro 9000 Printer, so can not see any reason to compromise with generic ink. So far, Amazon has the best price for the real thing. Sometimes I think the manufactuers should give you the printers for free if you obligate yourself to purchase ink from them. Comparatively, the price was not too bad for this.

There's not much to say about printer ink cartridges. Either they're the right ones for your printer or they ain't. These are right for the Canon PixmaPro 9000. All replacement cartridges are overpriced. The price on this pack is about the lowest I have found so far.

I own the PIXMA iP6600 Canon printer which has only 6 slots for the CLI-8 ink tanks leaving out the Green and Red tanks. However, purchasing this 8 pack, with no use for the Green and Red tanks, ended up pricing out to be the equivalent of purchasing the Canon CLI-8 4-Color Multipack Ink Tanks ($43) and then the Canon CLI-8PM Photo Magenta Ink Tank ($14), and Canon CLI-8PC Photo Cyan Ink Tank ($14) Seperately. Of course, shipping is also free thru Amazon with ground shipping so my total which would have been around $71 for 6 tanks ended up being just $75 for the 8 pack. $4 more for $28 worth of new tanks.



Obviously I have no use for the CLI-8 Green & Red tanks but they retail for $14 a piece so maybe I'll just sell them or give them to a friend who has the PIXMA Pro9000. Just a suggestion to those of you looking for ink. (*If prices change since I've typed this review I apologize)

Canon ink is a very good product. I have had not problems in the printer or on the different papers, clothe and vellums I have used it with. I created clothe banners with the inks and they hold up well at art shows.

The Canon cli-8 8 packaging is really handy to be able to buy all the colors I need at once. I use the Canon pro9000 13" wide printer. The red and green inks are a great addition to the ink series for great colors for my art prints.

I always purchase my large 8 pack from Amazon for the value. Great price and great shipping. - Canon - Pixma - Pro 9000 - Pro9000'


Detail Products
Detail Reviews
Click here for more information


Large Format Printer - pixma, pro9000 pro9000 Large Format Printer - pixma, pro9000

Ipod Nano Accessories - ihome, ipod charger


I too had read a million reviews for a million products. I decided to risk it with this since most of the reviews were good. I have A 4TH GENERATION NANO- and yes there is an adapter for it. We listen to it everyday. IT CHARGES YOUR IPOD WHILE DOCKED. The sound is great. The color change is cool. I wanted something small that sounded great. I use it in every room of the house, especially the kitchen while I am preparing meals. The sound is great for such a small cube. I would recommend this to anyone of any age. In a day where most things don't do what they say in the advertisement, finally something that exceeds those promises. You won't go wrong with this one. iHome iH15 LED Color-Changing Speaker System with Built-In Subwoofer for iPod

Overall, 4-stars, pretty good.



The sound is pretty decent. Forget deep, rich bass that others describe. Sounds better than most "mini-speakers" systems, though. Sounds like a small boom-box. At least the sounds are well balanced and articulated, not muddy or distorted.



It can also get pretty loud. Surprisingly, the bass response seems better at high volume levels.



The look of the cool, color changing cube is awesome. It has three modes:



> solid color of your choice;

> revolving colors, changing every few seconds;

> constantly oozing through the whole spectrum.



It's the third mode that's the coolest. It's dim enough to make a nice night-light without lighting up the whole room. And the light stuff works whether the sound is on or off, and it's easy to turn the light off when the sound is off as well.



CON - It has no clock, and no "auto on" feature. I had expected to leave it on and use my iPod's alarm to turn on, thus playing music to wake me up. However, it does not appear to work. When docked, the iPod's alarm does not go off. Maybe I should try it again with the iPod on, but not playing a song.



So overall, it's very nice.

I've had this for 3 months and have become obsessed with it -- I use it in a 300 sq-ft room, and it sounds great -- PROS/CONS follow.



PROS

Compact and lightweight -- it's just under 6"x6"x6" and maybe weighs a pound? Very easy to transport. It has little rubber feet that grip it to a flat surface.



Surprisingly good, rich sound quality -- I'm not an audiophile by any means, but would rate this very highly for the size and especially for the price. You can't adjust the bass or anything else, but the default is just fine.



Works overseas (100-240V) -- I took this with me while living abroad, and it works great with a simple Euro-plug converter. The plug is also relatively small and light (about 3"h x 2"w x 1"d), and easy to pack.



Charges iPod in its case -- I have the Griffin mirrored case (open bottom) over a 7G classic iPod, and it just barely fits, but it does fit. Also there are several dock adapters so you can use it with other iPod models.



Versatile -- The 3.5mm auxiliary jack allows you to use this with any device supporting a standard male-to-male input cable. It would be nice if a cable were included, but at this price, I can't really complain. Sound quality remains high across devices (I've used it with a Sharp tube TV and MacBookPro). It works with an auxiliary device plugged in, while the iPod is charging in the dock (w/the iPod turned off/paused). So you can use it as a laptop speaker, and keep the iPod docked to charge.



CONS

iPod alarm doesn't work with it -- I've had this problem with other speakers too, so I don't penalize this one too much for what could be an iPod-related problem. I use the speaker with my Mac laptop alarm, via a long (20') 3.5mm inline aux cable, and it works well.



Volume buttons are a little sticky -- You have to press them a few times to register a perceptible change. I prefer the touch sensitive buttons that JBL uses on my OnStage and Harmon Kardon sticks. It also takes a few seconds after turning on your iPod for the sound to "catch up" to the existing speaker volume.



No mute button -- You have to press the off button. Not a big deal, but worth mentioning.



TAKE IT OR LEAVE IT

Color light -- The stock photo that iHome uses is a bit deceptive. The colors don't change into solid "flat" colors, but into glowing color-lights. You can let it cycle through the colors or freeze it on the color of your choice. It's fun for 5 minutes, or, if you're 8, 5 years. Then you turn it off completely.



Carrying handles -- The handles are incorporated into the speaker as a curved piece protecting each of the 4 grills. This is a clever concept, but it's kind of disconcerting to scrape the grill fabric with your fingernails when using the handles.

I loved this product. LOVED IT. I never had a problem with it, and, in my small office, it had great sound. However, four months after purchase, it stopped responding. None of the control buttons work - although the unit still charges my iPod and lights up. It is past the 30 days I could return it to Amazon.com and iHome will only look at it for $25.00. Consequently, I am out of luck and would not recommend this product due to spotty longevity. - Ipod Accessories - Ipod Dock - Ihome - Ipod Charger'


Detail Products
Detail Reviews
Click here for more information


Ipod Nano Accessories - ihome, ipod charger ipod dock Ipod Nano Accessories - ihome, ipod charger